Search found 60 matches

Go to advanced search

by Jed118
Sat May 18, 2013 1:19 am
Forum: Project Cars
Topic: Project Stellarion D50
Replies: 0
Views: 3851

Project Stellarion D50

Many of you here will think this is travesty, but I picked up a Conquest (with a friend, we split it) for $600.

The head is cracked because of the wastegate being stuck closed, but the engine does turn.

I'm pulling the engine/trans combo out of this car, separating it from the G54B and attaching ...
by Jed118
Sat May 18, 2013 12:59 am
Forum: Swap Mechanical
Topic: Question about viability of a G54B
Replies: 2
Views: 3299

OK so apparently the head cracked because the wastegate stuck closed.

Do any forum members have a cheap head I could purchase?

Are there any wiring diagrams for the ECU and sensors? I imagine (after I saw the distributor still had a vacuum advance timing on it) the wiring harness isn't too ...
by Jed118
Fri May 17, 2013 9:43 am
Forum: Swap Mechanical
Topic: I found a car with a narrowblock in RWD configuration!
Replies: 6
Views: 5278

For a minute I thought there was some adapter or something for the wide/narrow.

Good stuff. Thanks guys.
by Jed118
Wed May 15, 2013 3:22 pm
Forum: Swap Mechanical
Topic: Question about viability of a G54B
Replies: 2
Views: 3299

Question about viability of a G54B

Hello,

I am picking up a fairly worn Conquest this Friday (non runner) pretty much for its transmission. Don't worry, my friend is putting an SBC into it.

Now, assuming the engine isn't seized, how good of a motor is the 2.6? My original plan was to put a 2.0 narrowblock (I have several KM132 ...
by Jed118
Wed May 15, 2013 2:59 pm
Forum: Swap Mechanical
Topic: I found a car with a narrowblock in RWD configuration!
Replies: 6
Views: 5278

How would I use a wideblock engine on a narrow block trans?
by Jed118
Tue May 14, 2013 12:12 am
Forum: Swap Mechanical
Topic: I found a car with a narrowblock in RWD configuration!
Replies: 6
Views: 5278

I found a car with a narrowblock in RWD configuration!

Unfortunately it is prohibitively rare and only available to Canada.

It is a 1987 (Only) Hyundai Stellar and it will have the G63B installed.

I found this out the hard way when I drove to Buffalo (2 hours each way) to get a new engine (G64B from a Dodge D50) and went to remove the rear plate to ...
by Jed118
Fri Aug 12, 2011 3:57 pm
Forum: Swap Electrical
Topic: Running carbs - No distributor?
Replies: 9
Views: 8989

Haha, here we go!

http://www.autosportlabs.net/Ford_EDIS_ ... nformation
by Jed118
Fri Aug 12, 2011 1:01 pm
Forum: Swap Electrical
Topic: Running carbs - No distributor?
Replies: 9
Views: 8989

Shit, I was hoping that CAS would have some springs and weights in it... :X

Hmm, I wonder if I can just use the computer to do the ignition... Are these computers fussy? Do they need to have all sorts of signals coming in from other management modules or sensors so that they work, or is the ...
by Jed118
Thu Aug 11, 2011 5:43 pm
Forum: Swap Electrical
Topic: Running carbs - No distributor?
Replies: 9
Views: 8989

Running carbs - No distributor?

Guys,

There is no distributor per-se on the DOHC, but there is some sort of thing at the back of the head - how do I get that to trigger my ignition? I have a points-style-converted-to-a-pcikup-sensor setup (one trigger wire running to an MSD box then to a distributor via single coil - MSD 6 ...
by Jed118
Tue Aug 09, 2011 6:27 pm
Forum: Swap Mechanical
Topic: A couple questions about 2.3L stroker...
Replies: 3
Views: 2919

A couple questions about 2.3L stroker...

...My original plan of using a 4G64 SOHC fell down the tubes (again) but I will not be discouraged, for I have the following parts:

1x 1987 6 Bolt (Hyundai Stellar) 2.0L block
1x 1989 G4CS (Hyundai Sonata) 2.4L crank
1x 1991 4G67 (Hyundai Elantra) 1.8L head

I've decided to feed it with two DCOE ...
by Jed118
Tue Aug 09, 2011 6:19 pm
Forum: Marketplace
Topic: FS: Dodge D-50 4G64 RWD EFI intake manifold SOHC
Replies: 2
Views: 2791

DISREGARD ALL (EVEN DELETE) POST INFO!

APparently, because of Ontario's Retire your Ride program, the junkyard is not allowed to sell any emissions part of that car.

Great.

No engine for me. Flesherton just scrapped their D50 too, just today, so I am not happy.

However I have a backup plan... :D
by Jed118
Tue Aug 09, 2011 2:29 pm
Forum: Marketplace
Topic: FS: Dodge D-50 4G64 RWD EFI intake manifold SOHC
Replies: 2
Views: 2791

I won't know if they included it until Saturday.

I can probably snag the ECM, but the harness... How much is it worth to you? I'll pitch that to the wreckers and see what they say.
by Jed118
Tue Aug 09, 2011 2:25 pm
Forum: Project Cars
Topic: 1987 Hyundai Pony 4G64 SOHC
Replies: 1
Views: 3644

1987 Hyundai Pony 4G64 SOHC

I'm back, albeit I doubt anyone remembers me: I had (at the time) dreams of putting in a G54B into a Pony... Well, those dreams were shattered yesterday when I drive 1.5 hrs one way to a wreckers to see an "Astron" from a 1986 Caravan - It had the weirdest water pump setup I had ever seen, which was ...
by Jed118
Tue Aug 09, 2011 1:00 pm
Forum: Marketplace
Topic: FS: Dodge D-50 4G64 RWD EFI intake manifold SOHC
Replies: 2
Views: 2791

FS: Dodge D-50 4G64 RWD EFI intake manifold SOHC

So I've finally picked up this engine (my Saturn 4G32 bit the dust at Mosport last year) to upgrade into my Hyundai Pony. It is from a 1991 EFI Dodge D-50.

http://smg.photobucket.com/albums/v608/Jed118/?action=view&current=IMG_0002.jpg

I have no need for the manifold, as I am attaching some ...
by Jed118
Mon Mar 23, 2009 12:40 pm
Forum: Project Cars
Topic: Hello from Canada!
Replies: 1
Views: 2656

Nice plate, I've got 587 on the end of mine, attached to a 4G powered Hyundai Stellar.

:P
by Jed118
Wed Mar 11, 2009 6:13 pm
Forum: Project Cars
Topic: 1987 Hyundai Pony M90 build
Replies: 6
Views: 8218

another trip to the wreckers yielded a BETTER tensionner pulley (5 rib) which I shall be machining down for smoothness. It's from a 1995 Lexus SC (forget what one) and it fits the supra bolt.

I went to Brafasco today and got parts to settle the lower mount, I'm going to weld them on Friday, as ...
by Jed118
Sat Mar 07, 2009 12:01 am
Forum: Project Cars
Topic: 1975 dodge colt gt 4g63 w/ W55 trans
Replies: 37
Views: 50251

Give me back my Pony motor!

Nice job, I've started doing that, just waiting on money to come in to purchase pistons.
by Jed118
Sat Feb 28, 2009 7:37 pm
Forum: Project Cars
Topic: 1987 Hyundai Pony M90 build
Replies: 6
Views: 8218

More updates:

I've been busy with school assignments, but two separate trips yielded the following components:

http://img.photobucket.com/albums/v608/Jed118/DSCN6440.jpg

This is the exhaust plate on the supercharger. I had to cut it at the flange and I'm going to have it welded thusly:

http ...
by Jed118
Tue Feb 03, 2009 6:56 pm
Forum: Project Cars
Topic: 1987 Hyundai Pony M90 build
Replies: 6
Views: 8218

There are a number of possibilities to drive the SC, but first

Using the formula

Boost (psi) = (PR x 14.7 x V / C/2 ) - 14.7 - I

and plugging in the values (in inches)

5.356 (crank) and 3.146 (M90) is roughly 1.7

PR = 1.7
V = The M90 is 90 cubic inches or 1475 cc
C = 1,597 (/2 is ~798) It's ...
by Jed118
Sun Feb 01, 2009 1:12 pm
Forum: Project Cars
Topic: 1990 mitsubishi rwd van twin cam conversion.
Replies: 10
Views: 10720

Holy 15 MPH bumpers batman!

:shock:
by Jed118
Sat Jan 31, 2009 7:50 pm
Forum: Project Cars
Topic: 1987 Hyundai Pony M90 build
Replies: 6
Views: 8218

Excellent. I actually found that site 5 days ago, but thanks are still in order

I have done some initial calculations: to get 5.6 PSI I need a ratio of 0.75:1 (on a 1600 cc motor)

I will double check this. I have the 3.5 inch wheel on the M90, so im gonna go out and find at least a 5 rib pulley ...
by Jed118
Wed Jan 21, 2009 12:03 am
Forum: Project Cars
Topic: 1987 Hyundai Pony M90 build
Replies: 6
Views: 8218

Does anyone know how to calculate the amount of boost based on the pulley diameters?
by Jed118
Sat Jan 17, 2009 6:17 pm
Forum: Project Cars
Topic: 1987 Hyundai Pony M90 build
Replies: 6
Views: 8218

1987 Hyundai Pony M90 build

While I wait for my 4G64 to return from the shop, I am going to be doing this. Not a 4G63 or 4, but a 4G32.

http://torontohyundaiclub.forumup.com/v ... iclub#1759

If you guys have any ideas/thoughts, let me know. This would be my first SC install, ever.
by Jed118
Sat Dec 27, 2008 9:18 pm
Forum: Project Cars
Topic: '86 Hyundai Stellar 4G63 swap
Replies: 16
Views: 21336

He also advised me to do the same: and I will!

Heh, if you want, I have a stock (BRAND NEW) headlamp housing for the stellar... I think passenger side.

It's been sitting in a warehouse forever... do you want it?
by Jed118
Tue Dec 23, 2008 11:06 pm
Forum: Project Cars
Topic: 4G63 FC-Anyone here?
Replies: 44
Views: 34271

I'm no master welder, but the welds in this pic... Image

:!:

Also, don't you need an alternator to have a belt to work? :lol:

In any case, it's much farther along than mine.

Did you keep the balance shafts in?
by Jed118
Mon Dec 22, 2008 5:50 pm
Forum: Project Cars
Topic: '86 Hyundai Stellar 4G63 swap
Replies: 16
Views: 21336

I've only ever seen one 4G32 belt driven... it was in a guy's slammed pony pickup truck (also carbed) that he had swapped in.

The 4G32 and 4G33 (as well as the 1.2L version, I think 4G36) that were used in the Pony/Stellar are ALL chain-driven. I've not ever seen a belt drive in a Pony otherwise ...
by Jed118
Sun Dec 21, 2008 10:41 pm
Forum: Project Cars
Topic: G4CS (4G64) pics of build up
Replies: 1
Views: 3847

Here's what I'm thinking for the carbs...

http://img.photobucket.com/albums/v608/Jed118/DSCN6356.jpg

http://img.photobucket.com/albums/v608/Jed118/DSCN6357.jpg

http://img.photobucket.com/albums/v608/Jed118/DSCN6358.jpg

Here's an "exploded" view of the components:

http://img.photobucket ...
by Jed118
Sun Dec 21, 2008 2:19 pm
Forum: Project Cars
Topic: 1980 Mitsubishi Eterna GSR from New Zealand (56k no)
Replies: 18
Views: 16543

I have the exact same problem with my front suspension... the damned spindle is INTEGRATED into the shock!!

I found a way around it though... there's a similar car (hyundai Stellar) that uses almost the same parts except... the shock comes APART from the spindle! Glorious news for me!

Also, I've ...
by Jed118
Sat Dec 20, 2008 8:41 pm
Forum: Project Cars
Topic: G4CS (4G64) pics of build up
Replies: 1
Views: 3847

G4CS (4G64) pics of build up

I've basically only dismantled it for now... taking measurements, saving for pistons/head work



http://img.photobucket.com/albums/v608/Jed118/DSCN6354.jpg

Dirty block!

It looks like I may have to .020 it...

http://img.photobucket.com/albums/v608/Jed118/DSCN6353.jpg

I couldn't get the ...
by Jed118
Thu Dec 18, 2008 5:05 pm
Forum: Marketplace
Topic: 90 degre water outlet
Replies: 4
Views: 4057

Negative. I called it first. :twisted:
by Jed118
Wed Dec 17, 2008 4:39 pm
Forum: Marketplace
Topic: 90 degre water outlet
Replies: 4
Views: 4057

YOu still have it? Check your PM!
by Jed118
Wed Dec 17, 2008 4:38 pm
Forum: Project Cars
Topic: '86 Hyundai Stellar 4G63 swap
Replies: 16
Views: 21336

You have a SOHC carburated 4G63? What parts do you need! I have a complete running engine, i'd be willing to part it out (because I won't need it any longer)
by Jed118
Wed Dec 17, 2008 1:36 am
Forum: Swap Mechanical
Topic: Important Question! About 4G63 vs 4G67 front dress parts!
Replies: 15
Views: 5645

That's what I thought. I'm going to look into it further!
by Jed118
Tue Dec 16, 2008 8:53 pm
Forum: Swap Mechanical
Topic: Important Question! About 4G63 vs 4G67 front dress parts!
Replies: 15
Views: 5645

^^^ Excellent!

However, Hyundai produced these on a license and made them themselves... anyways, I'd have to see about that... I seem to be perpetually stuck with these odd ball engines!

Also, exactly why can't I use the 4G64 oil cover and bits?
by Jed118
Tue Dec 16, 2008 7:59 pm
Forum: Swap Mechanical
Topic: Important Question! About 4G63 vs 4G67 front dress parts!
Replies: 15
Views: 5645

What about a 1993 Elantra?
by Jed118
Tue Dec 16, 2008 7:56 pm
Forum: Swap Mechanical
Topic: Cam equivalency question
Replies: 13
Views: 5147

The pictures are really bad, the head is actually decent. The bearings that are damaged are the ones that form "caps", the top part if you will: It's not a problem for me to go out and grab these two parts, a cam, two rockers and a couple lifters (for good measure, just in case)

No part of the head ...
by Jed118
Tue Dec 16, 2008 7:29 pm
Forum: Swap Mechanical
Topic: Important Question! About 4G63 vs 4G67 front dress parts!
Replies: 15
Views: 5645

yeah you read my mind, I went to eBay and looked at 1994 elantra gaskets and 1994 Laser/Eclipse gaskets - the very same.

The head was off a 6 bolt, as is the block. My friend (turbo stellar) thinks they may be the same too, but not the 1.6 it has a different water pump and all.

I'm going to order ...
by Jed118
Tue Dec 16, 2008 6:50 pm
Forum: General
Topic: just curious
Replies: 9
Views: 4927

Technically, if I put back on the distributor pickup and put a battery in it, I have a (not so impressive) 2 Liter SOHC Pony 4G63... removing that soon though.
by Jed118
Tue Dec 16, 2008 6:44 pm
Forum: Swap Mechanical
Topic: gearbox not selecting gear
Replies: 23
Views: 12897

No Pony and Stellar in the US.

The first ones were catalyst-free, so Cali held them back... fools!

I don't see why they didn't allow the 1987 and up Stellars (later fuel injected... the ONLY hyundai to have TBI) into the US and rebadge it as a Sonata (which is what directly replaced it) I mean ...
by Jed118
Tue Dec 16, 2008 6:36 pm
Forum: Swap Mechanical
Topic: Cam equivalency question
Replies: 13
Views: 5147

Yeah I know... I found a DSM site that explains EVERYTHING in detail... except I can't find any cam information!
by Jed118
Tue Dec 16, 2008 6:24 pm
Forum: Swap Mechanical
Topic: Important Question! About 4G63 vs 4G67 front dress parts!
Replies: 15
Views: 5645

Well, to be honest, I don't know what I'm looking at! The two oil covers in the link look identical to me... and they're cleaned up parts. I'm going to be dealing with cold weather, dirt, and snow on EVERYTHING plus it's a 1 hr drive to this wreckers so I want to be as sure as possible.
by Jed118
Tue Dec 16, 2008 5:13 pm
Forum: Swap Mechanical
Topic: Important Question! About 4G63 vs 4G67 front dress parts!
Replies: 15
Views: 5645

Important Question! About 4G63 vs 4G67 front dress parts!

The parts interchangeability on this table here:

http://www.projectzerog.com/sohc-dohc.shtml

Question: Could I use 4G67 parts instead of 4G63? Reason I ask is that the junkyard I normally go to has a lot of "useless" 1.8 elantras that they wouldn't mind me taking oil covers and pumps and little ...
by Jed118
Tue Dec 16, 2008 7:28 am
Forum: Swap Mechanical
Topic: gearbox not selecting gear
Replies: 23
Views: 12897

Your first picture had interference (more than likely from an actual picture of the screen... the scanning lines and the shutter speed aren't matching the scan lines of the old tube monitor. :!: ) so I could not read much off it.

You could, of course, hit "print screen" directly adjacent to F12 ...
by Jed118
Mon Dec 15, 2008 11:16 pm
Forum: Swap Mechanical
Topic: stripped head bolts
Replies: 13
Views: 8602

That same procedure was taken by me: Smash a bigger bit, use an electric impact gun... fail? Grind headbolt down, remove head, grind studs down on sides, heat, remove with vice grips.

Not very fun, but on a rare 4G32 SOHC head (well, rare now anyways), you gotta do what you gotta do!
by Jed118
Mon Dec 15, 2008 11:04 pm
Forum: General
Topic: Late 70's early 80's challengers found what to take?
Replies: 25
Views: 30986




http://i35.photobucket.com/albums/d182/Professor-Quest123/steering/SC-77.jpg


dj verified (last night) that cross member under that 4 banger was out of a d-50. COOL! BOLT-IN!

Schnieder will RE-GROUND *YOUR CLEAN* mechanical cam! HINT!
magic words:


Pony uses the same steering box. Maybe ...
by Jed118
Mon Dec 15, 2008 10:50 pm
Forum: Swap Mechanical
Topic: gearbox not selecting gear
Replies: 23
Views: 12897

[quote="Professor Quest"

http://i35.photobucket.com/albums/d182/Professor-Quest123/clutch/CL-3.jpg [/quote]

That's a Hyundai Stellar (4G63) KM132 unit!

Tell you what, mate, I never had a problem with ANY cable operated clutch KM series transmission! Ever! That includes swaps I did at a young ...
by Jed118
Mon Dec 15, 2008 10:16 pm
Forum: Swap Mechanical
Topic: Cam equivalency question
Replies: 13
Views: 5147

Cam equivalency question

I'm aggresively dismantling the head as it is going to a shop to get cleaned up, plained and a valve job done. During the dismantling process, two cam bearings were found to be worn to the touch, as well as two rollers were quite hard to operate. Also, I don't know what these are called, but they're ...
by Jed118
Wed Nov 05, 2008 4:27 pm
Forum: Project Cars
Topic: '86 Hyundai Stellar 4G63 swap
Replies: 16
Views: 21336

Yeah that engine in the Pony (the stock 4G63 Stellar 2.0) is from one of his parts cars. We installed it one summer afternoon (take pony motor out, put aside - take stellar motor out of stellar, set aside, swap pressure plate - pilot bearing - put it back together and iron out the differences 10 hrs ...
by Jed118
Wed Oct 29, 2008 10:26 am
Forum: Swap Mechanical
Topic: Additional 4G64 w/ DOHC head questions
Replies: 6
Views: 4806

The head will receive complete treatment (3 angle, shave 0.030, port + polish) anyways. I want to pull this mill apart to inspect it, and while it's apart, I'm gonna add new pistons. I have heard that the stock pistons and valves will create compression 13:1 for about 1 second, then the valves will ...
by Jed118
Tue Oct 28, 2008 12:03 pm
Forum: Project Cars
Topic: '86 Hyundai Stellar 4G63 swap
Replies: 16
Views: 21336

Interesting... I too have a stellar (1987, so it uses the counterbalanced SOHC 4G63 2.0), and on top of all that, I have a 1984 Pony (not available in the US) WITH THAT SOHC 4G63 in it! I had no problems putting in the 4G63 where the 4G32 was: everything bolted right in! The stock Pony mounts were ...

Go to advanced search