4g63t rwd flywheel

All the oily, spinning bits

Moderators: DJpowerHaus, mattmartindrift

Post Reply
LILVR4
Knowlege Seeker
Posts: 17
Joined: Sat Nov 14, 2009 2:17 am

4g63t rwd flywheel

Post by LILVR4 »

hi there im putting a 4g63t dohc egine into my sigma out of a vr4 galant im useing a 5speed sigma box with i beable to use vr4 flywheel and clutch or will i need sigma flywheel and clutch, if so will a 4speed flywheel and clutch work?
Top
jeffball610
Too Much Time on His Hands
Posts: 619
Joined: Wed Feb 22, 2006 5:29 am
Location: Las Vegas, NV

Post by jeffball610 »

Measure the old flywheel. My guess is that the VR4 flywheel will not fit. Most of the RWD swaps (including Billhousings) use the FWD diameter ring gear flywheel. But again, just measure the old one if you still have it to be sure.
Do it in a Datsun!
1972 Datsun 510
7-bolt 4G63T, EVO 9 pistons and rods, Garrett GT3076R, "flipped" stock intake, Toyota R154, Z31 R200 w/ CVs
Top
EVOMINUS
Knowlege Seeker
Posts: 10
Joined: Thu Apr 09, 2009 3:24 pm

Post by EVOMINUS »

jeffball610 wrote:Measure the old flywheel. My guess is that the VR4 flywheel will not fit. Most of the RWD swaps (including Billhousings) use the FWD diameter ring gear flywheel. But again, just measure the old one if you still have it to be sure.
excuse the off topic but how can you tell that its a rwd,fwd or 4wd?
Top
EVOMINUS
Knowlege Seeker
Posts: 10
Joined: Thu Apr 09, 2009 3:24 pm

Post by EVOMINUS »

noone???????
Top
DJpowerHaus
Sir Post A Lot
Posts: 1779
Joined: Wed Apr 07, 2004 3:24 pm
Location: Baltimore, MD
Contact:
Contact DJpowerHaus

Post by DJpowerHaus »

I believe that the AWD ring gear is a smaller diameter than the FWD ring gear. The actual measurements though.. I don't have them handy.
Image
Getting the engine bolted in is about 10% of the way there.
The next 80% can go quickly with help and skill.
That last 10% takes about as long as the 90% that came before it.
Top
LILVR4
Knowlege Seeker
Posts: 17
Joined: Sat Nov 14, 2009 2:17 am

Post by LILVR4 »

would they flywheel off my 4g32 bolt up?
Top
DJpowerHaus
Sir Post A Lot
Posts: 1779
Joined: Wed Apr 07, 2004 3:24 pm
Location: Baltimore, MD
Contact:
Contact DJpowerHaus

Post by DJpowerHaus »

What diameter is the ring gear? How big of a clutch can it accept? How many bolts does it have for the crank? Does it have a pilot bearing?
Image
Getting the engine bolted in is about 10% of the way there.
The next 80% can go quickly with help and skill.
That last 10% takes about as long as the 90% that came before it.
Top
darrs7
Knowlege Seeker
Posts: 1
Joined: Wed May 14, 2014 2:56 am

Post by darrs7 »

Hi. any im updates on this one?

Im also in the process of doing engine transplant
its a 76 Lancer A72
has a 4g32 and a KM119 (5spd)

also wondering if the
flywheel off my 4g32 bolt up?
Top
DJpowerHaus
Sir Post A Lot
Posts: 1779
Joined: Wed Apr 07, 2004 3:24 pm
Location: Baltimore, MD
Contact:
Contact DJpowerHaus

Post by DJpowerHaus »

Try it out, post what you find.
Image
Getting the engine bolted in is about 10% of the way there.
The next 80% can go quickly with help and skill.
That last 10% takes about as long as the 90% that came before it.
Top
tektic
Knowlege Seeker
Posts: 20
Joined: Wed Dec 05, 2012 9:22 am

Fwd FW + clutch

Post by tektic »

I also have a some flywheel question.

1990 g63b wide block 1987 starion trans

Can A fwd dsm clutch, pressure plate and flywheel be used with a starion trans connected to a wide block? What starter and plate is required? Where do I find the specs for the pilot bearing install? Am I forgetting anything I need to make this work in my 1995 mighty max?

Thank you
Top
Post Reply

Return to “Swap Mechanical”