Professor Quest parts sale!!!

For Sale / Want to buy / Trade

Moderators: DJpowerHaus, mattmartindrift

Post Reply
Professor Quest
Addict
Posts: 136
Joined: Sun Nov 30, 2008 8:25 pm
Location: High Desert, Albuquerque, NM. The NUCLEAR state!

Professor Quest parts sale!!!

Post by Professor Quest »

TO ALL:
It has been reported on Starquestclub that Wayne aka Professorquest has passed away from health complications.
MainstreaM


ENGINE/FLYWHEEL/CLUTCH PARTS

2.6L Turbo Cranks, $20+s&h. (+ any exsisting machining & balance)
Image

2.6L Turbo Blocks, $20+s&h (+ any exsisting machining)

Image

The history: I'm getting alot of flac from a particular "admin",
cause he THINKS these donor cars were worthy of restoration!
:roll:.... :lol: :lol: :lol:

Starquest that were given to me, or sold very cheap
(get rid of their trash)
are a storage, PITA! :roll: These Starquest were DONE-FOR, already! :x

Several engines were given to me, (wanted a V-Eight, etc.)
some we purchased from Super-U-Pull-It...
RUST FREE & SUPER CLEANED via OUR efforts! :wink:


We grab what we want...then have it hauled away ASAP!
(don't want junk/scrap cars around us! :oops: do you? )

2.6L Engines, Trans, steering/suspension, rear axle assembles.
---------------------------------------------------------------

2.6L Wiseco Forged Pistons w/rings, high compression, 6cc dish, $400+ s&h

CAUTION! Using hypereutectics pistons is a NO-NO on turbocharged engines!
Says so... :roll: in most of the catalogs!

Image

2.6L AMC "Spainish" head, valve guides dropped for maximum cam lift,
no egr port, no jet valve channel, ported/polished, $400+s&h! :shock:

CAUTION! There are several, re-cast Aluminum heads, that will fail
soon enough! :roll: Many members have been RIPPED-OFF, thinking
the price was good. You get what you pay for. :x


Image

2.6L Mechanical Rocker Arms w/Mechanical Shafts & new,
longer, adjustment screws w/locking nuts. (non jet valve type)
$150+s&h 8)

Image

2.6L New, Mechanical or Hydrualic camshafts, $110+s&h

Image

2.6L CLOYES T chain kit, $80+s&h (Cloyes is the best!)

Image

Image

2.6L Cloyes T-chain kit w/ BSEK & t-cover gasket/seals & o-ring $110+s&h.

Image

PQ's T-chain kits come with the TSB, HD parts! 8)

Image

2.6L Head shim. .020" to restore the cam timing when heads are machined.
$30+s&h
Image

2.6L Harmonic Dampers/ Front Pullys. $45+s&h.

Image

2.6L ALUMINUM Front Pulley. $65+s&h

Image

2.6L STEEL Flywheels, 15lbs, 240mm disc size w/dowel pins, Fits 83-89s,
$275+s&h

Image

2.6L Fidanza Aluminum FWs, 11lbs, 225/240mm disc size, w/dowel pins, Fits 83-89s
$275+s&h

Image

A.C.T. 240mm, HD street clutch w/both bearings & alignment tool (5pc)
$275+s&h

Image

YOU WON'T BELIEVE...how much you improved your car & clutch action!
10mm adjustment rod (vs. 8mm) and NO RUBBER SLUG
(that wears out) new, clevis pin, washer & cotter pin, too!
$40+s&h

Image

Mitsu's DUROMETER rubber is superior to ALL aftermarket JUNK! :roll:
$65+s&h
Image

OEM (Nabco) CLUTCH Master Cylinder w/adjustment rod & clevis pin.
$75+s&h.

Image

2.6L Turbo Exhaust Manifold, stress relieved, machined mouting surface.
$150+s&h


Image

2.6L Mitsu's, used 12A Turochargers *TESTED* :wink: $65+s&h
Image


Contact PQ at: waynescoolworld@netzero.net or call (505)299-9012


More adds coming soon! 8)














Last edited by Professor Quest on Fri Mar 01, 2013 10:57 pm, edited 30 times in total.
The million dollar manual and AFFORDABLE parts too! USE IT!
http://starquest.i-x.net/viewforum.php?f=12
email: waynescoolworld@netzero.net USE IT!
Top
Professor Quest
Addict
Posts: 136
Joined: Sun Nov 30, 2008 8:25 pm
Location: High Desert, Albuquerque, NM. The NUCLEAR state!

Post by Professor Quest »

MISC.

Super lighweight glove box doors!
Early Starquest did not have the 5lbs doors! :shock:
BOLT-INS! $65+s&h



Image

Face/Foot Vacuum Servo to replace the accordian-type
like pictured above. $30+s&h

Image

Grills. $110+s&h
Image

This OBSOLETE duct was used in non-a/c Starquest.
CAKE...to install and removes several lbs! $65+s&h

Image

Mechanical fan, shroud & thermal clutch conversion. $150+s&h.

Image

The SCOOP! $100+s&h. 8)
http://www.starquestclub.com/forum/inde ... pic=135899


Last edited by Professor Quest on Thu Mar 14, 2013 8:23 pm, edited 10 times in total.
The million dollar manual and AFFORDABLE parts too! USE IT!
http://starquest.i-x.net/viewforum.php?f=12
email: waynescoolworld@netzero.net USE IT!
Top
Professor Quest
Addict
Posts: 136
Joined: Sun Nov 30, 2008 8:25 pm
Location: High Desert, Albuquerque, NM. The NUCLEAR state!

Post by Professor Quest »

DRIVETRAIN
Male coupler, Female Torque Tube, $300 for the pair.
If one is worn...so is the other. :cry:
Image

Rebuilt, complete, 5 speed driveshafts with Napa, HD u-joints. $110+s&h
Ready to install!

Image

Rebuilt Rear Diff, 87 $150+s&h, 88/89 $200+s&h (no TT parts)

Image

83-87 non-intercooled, 86-87 intercooled, 88-89 intercooled parts,
Spindels, CV shafts, Diff. Assembles. Contact us for specifics.
Image


Last edited by Professor Quest on Thu Mar 14, 2013 7:23 pm, edited 6 times in total.
The million dollar manual and AFFORDABLE parts too! USE IT!
http://starquest.i-x.net/viewforum.php?f=12
email: waynescoolworld@netzero.net USE IT!
Top
Professor Quest
Addict
Posts: 136
Joined: Sun Nov 30, 2008 8:25 pm
Location: High Desert, Albuquerque, NM. The NUCLEAR state!

Post by Professor Quest »

FUEL related parts
Fuel Injectors w/install hardware. $220+s&h
Fuel Injectors w/pigtails w/install hardware. $250+s&h
KILLER... :twisted: NON-LEAK O-RINGS!
Image

FPR (fuel pressure regulator) which controls 36-38psi, when it's
not corroded inside, or it don't leak, internally. :x
$70+s&h.

Image

Bosch/PQ's Fat-Boys fuel pumps w/install kit.
$180 for standard pump w/kit
$210 for DCP (dampner circumvent pump) w/kit
+s&h
Lifetime Warranty when you use 2 inlete filters! 8)

Image
Corroded dampners restrict fuel flow, very common! :roll:

In-Tank filter $15 in-line filter, $25+s&h

Image

Installed: CAUTION! Failure to CLAMP, *ALL* nipples you'll
CAVITATE a new pump! = Ya fucked-up! :x
Image

HD, twin Fuel Pump relays. $60+s&h.


Image
Rebuilt, HP fuel hoses (Starquest have 3) $65 exchanged.
Greenline hose means, friendly to ETHANOL/E85!
($iliconed lined 8) )

Image

SS Braided is $90+s&h, exchanged.
Image

-AN conversion kit. (removes the dampner on fuel pump) $110+s&h

Image

"J" hoses, 12mm. Is your's old & stiff? :roll: ETHANOL! $25+s&h

Image

CLEAN...blank fuel tanks, $275+s&h
Image

86-89 Fuel Level Sender. $55+s&h EXCHANGED.
Image

Fuel Tank Nipple Unions. $55+s&h
Image

Filler Neck Hose. $17+s&h
Image

Fuel Pump Shelf. $55+s&h
Image

SOFT, accordian hoses. $65+s&h
Image

Fuel injector resistor pack. Keeps running voltage to about 9 volts.
$50+s&h.
Image

The RIGHT O2! $50+s&h. 8)


Image

Last edited by Professor Quest on Sat Mar 02, 2013 12:25 am, edited 25 times in total.
The million dollar manual and AFFORDABLE parts too! USE IT!
http://starquest.i-x.net/viewforum.php?f=12
email: waynescoolworld@netzero.net USE IT!
Top
Professor Quest
Addict
Posts: 136
Joined: Sun Nov 30, 2008 8:25 pm
Location: High Desert, Albuquerque, NM. The NUCLEAR state!

Post by Professor Quest »

ELECTRICAL

You'll need a BETTER ground, like some 88/89s had.
2 gauge Negative Cable that grounds the BODY first,
then onto the block.
83-87 used a 4 gauge, 88-89s some got a 3 gauge. :roll:

$65+s&h...MONSTER 2 GAUGE! :twisted:


Image

All Starquest had a STUD-MOUNTED positive terminal.
Our replacement is all BRASS! $9

You want a rear-mounted battery? Use this 5/16" (8mm)
isolated union block to make that conversion. CAKE! $20


Image

When rear-mounted battery, hook your Black/Red, positive cable
to this isolated union block. DONE! 8)


Image

Was your fusible link box in bad condition? :x
Used replacements are $65+s&h wo/links
Image

The Famous Five Failures...5 new fusible links, $55+s&h
Image

Relay box w/relays $65+s&h
Image

Would you like your volts & amps deliverd with ZERO FAULTS?
6 gauge wire + mil-spec terminals, crimped & solderd! :twisted:
$110 exchange+s&h
Image

Same price...but for the GM 105amp Alternator
Image

How many miles are on your Starquest? :roll: If over 100K... :?
WORN-OUT IGNITION SWITCHES become a HIDDEN, problem! :shock:
$65+s&h

Image

Rebuilt TURBO Dizzys! Turbo Dizzys are programed different to N/A
Dizzys! FACT!
$150+s&h EXCHANGE!
(Turbo dizzys have there own model #s stamped on the side)
Image

84-87 "Knock Boxes" $110+s&h
Image

ETACS...TESTED :roll: did you jump-start your Starquest with reversed
polarity? OOPS! :shock: $150+s&h
Image


Last edited by Professor Quest on Sun Mar 17, 2013 7:02 pm, edited 3 times in total.
The million dollar manual and AFFORDABLE parts too! USE IT!
http://starquest.i-x.net/viewforum.php?f=12
email: waynescoolworld@netzero.net USE IT!
Top
Professor Quest
Addict
Posts: 136
Joined: Sun Nov 30, 2008 8:25 pm
Location: High Desert, Albuquerque, NM. The NUCLEAR state!

Post by Professor Quest »

STEERING/BRAKES/SUSPENSION 8)
Sick of the leaks? :roll:
Rebuilt P/S boxes. $275+s&h EXCHANGE.
Image

Rebuilt P/S pumps $150+s&h


Image

You want... :roll: less trash & BS under your hood?
Go PQ's manual steering & extended, rebuilt columns
w/upgraded tilt-holding device, too!
$440+s&h (send back your cores for a rebate, too 8) )

Image

New, Raybestos, brake master cylinder. $100+s&h.
Image

Approved DOT built, SS coverd with a clear cover, $80 for 4
to replace the OEM, 8 hoses.

Image

Image

Image

Built by a Pro...for a PRO! 8)
Image

OEM Brake Boosters. $50+s&h.

Image

Need more room for MPI? :roll:

PQ's lightweight, Aluminum MC w/reservoir,
w/ a smaller diameter brake booster.
Bolt-ins! :twisted:
$175+s&h.
Image

Image

Image

TSB replacement parts...a MUST DO! 8)
Image

Need MORE room for your MPI? Move the booster
toward the firewall!
$20+s&h.

Image

LOOSE bearing races? :roll: Common enough!
Complete hubs w/bearings. $100+s&h.
Image

Real-deal Mitsu's rotors, rust free! $20ea.+s&h

Image
RUST FREE suspension parts! Front-Rear, left & right! X-memebers, too!
Image
Last edited by Professor Quest on Sun Mar 17, 2013 7:15 pm, edited 10 times in total.
The million dollar manual and AFFORDABLE parts too! USE IT!
http://starquest.i-x.net/viewforum.php?f=12
email: waynescoolworld@netzero.net USE IT!
Top
RobFijiStarion
Knowlege Seeker
Posts: 2
Joined: Tue Oct 07, 2014 10:53 pm

Post by RobFijiStarion »

I know this post is a little old but are these parts still available?
Top
Lunacy
Knowlege Seeker
Posts: 33
Joined: Sun Jul 06, 2008 2:40 am
Location: Auckland, New Zealand

Post by Lunacy »

RobFijiStarion wrote:I know this post is a little old but are these parts still available?
Read the post before yours. PQ passed away earlier this year, so don't think any of this stuff will be available
86 Starion EX Racecar 4g63t DOHC
Top
RobFijiStarion
Knowlege Seeker
Posts: 2
Joined: Tue Oct 07, 2014 10:53 pm

Post by RobFijiStarion »

Ooooooo..... Sorry to hear that.
Top
Post Reply

Return to “Marketplace”