FS- MAGNUS RWD intake manifold

oyayjoe · Post by **oyayjoe** » Tue May 22, 2012 11:46 am

SOLD!!!

gabytech · Post by **gabytech** » Tue May 22, 2012 4:17 pm

How much ??? Im really interested..

oppsss, sorry, didnt finished reading.. 700.. no disrespect or low balling the price, but for 300 more I can get a brand new Magnus V3 cast manifold, which is way better manifold than the aluminum manifold, with nitrous bungs installed and shipped to Puerto Rico... Im really interested in your manifold, but my offer is 500...

oyayjoe · Post by **oyayjoe** » Tue May 22, 2012 5:36 pm

gabytech wrote:How much ??? Im really interested..

oppsss, sorry, didnt finished reading.. 700.. no disrespect or low balling the price, but for 300 more I can get a brand new Magnus V3 cast manifold, which is way better manifold than the aluminum manifold, with nitrous bungs installed and shipped to Puerto Rico... Im really interested in your manifold, but my offer is 500...

this is not a typical magnus aluminum intake manifold this was built custom for the MAP performance 4g64 rx7 drag car which made well over 900whp. Notice there are no welds on the where the flange meets the runners or where the runners meet the manifold. That's because that whole piece is cnc'd billet aluminum velocity stacks. This manifold is a monster and will outflow the v3 cast by far. Like i said this is a one-off custom built magnus piece. The cheapest i can do for you shipped to puerto rico is $580. Let me know, thanks.

oyayjoe · Post by **oyayjoe** » Tue May 22, 2012 5:37 pm

this manifold has nitrous bungs as well

gabytech · Post by **gabytech** » Tue May 22, 2012 6:04 pm

580 sounds fair... I can get the money by my next paycheck, which I get paid june 1st. If you havent sold it by then, Ill buy it for sure. Let me know if it sounds good and fair.. Thanks... Im doing a RWD conversion on my 2G Eclipse with 1G head...

oyayjoe · Post by **oyayjoe** » Tue May 22, 2012 6:12 pm

gabytech wrote:580 sounds fair... I can get the money by my next paycheck, which I get paid june 1st. If you havent sold it by then, Ill buy it for sure. Let me know if it sounds good and fair.. Thanks... Im doing a RWD conversion on my 2G Eclipse with 1G head...

sounds good to me. Get in contact with me when you get the money, thanks

gabytech · Post by **gabytech** » Tue May 22, 2012 6:17 pm

ok.. will get in contact with you when I have the money.. Whats the best way to contact you, at this forum, another forum, facebook, email, or phone ??? my personal facebook is gaby-tech@hotmail.com

davdbek95 · Post by **davdbek95** » Sat May 26, 2012 3:50 am

SALE FOR THROUGH I WILL TAKE IT OF YOUR HANDS ASAP.
REGARDS DAVID

oyayjoe · Post by **oyayjoe** » Sat May 26, 2012 7:22 am

Ok I will let u know if it falls through

oyayjoe · Post by **oyayjoe** » Fri Jun 01, 2012 2:28 pm

Gabytech are you still interested?

oyayjoe · Post by **oyayjoe** » Sun Jun 03, 2012 1:27 pm

Sale Pending

davdbek95 · Post by **davdbek95** » Wed Jun 27, 2012 5:28 am

Did the sale go through,as you stated that sale pending

Project Zero G Forums

FS- MAGNUS RWD intake manifold

FS- MAGNUS RWD intake manifold

Magnus RWD intake manifold

Re: Magnus RWD intake manifold

Magnus RWD intake manifold

Re: Magnus RWD intake manifold

Magnus RWD intake manifold

inlet manifold

Sale of manifold