Project Zero G Forums

so if its a wide block bell housing can i bolt a narrow bellhousing on?

hay there just wonting to know will the gearbox out of a l200 4x4 ute with the 2.6l petrol engine bolt up to a 4g63t dohc?

Hay there go after the site where you can buy the aftermarket water outlet
To move water outlet to the front of the 4g63t .

hay there i have some parts you need to change your sohc 4g63/4g64 to a dohc it everything from the front side of a dohc block
iv wreaked a vr4 4g63t engine

list of parts

Oil Pump Cover
Oil Pump Gear Drive
Oil Pump Driven
Oil Pump Sprocket
Crank Timing Sprocket
Timing Mark Plate
Timing Belt ...

well this is how i got it out didnt have any grease , this works a treat and hardy any mess if you dont mash it as hard as they do in video

check it out

grab some vogels or tip top, depending on your taste..

http://www.youtube.com/watch?v=VD9oz77E3lw

http://www.youtube.com/watch?v=ziuFFyJd4yE ...

how do i remove this bush peace out of the end of crankshaft , i think engine must have been a auto and my flywheel wont bolt up with it in there

http://i830.photobucket.com/albums/zz225/lilvr4/P1040998.jpg
http://i830.photobucket.com/albums/zz225/lilvr4/P1040996.jpg
http://i830.photobucket ...

hay there im just wondering i know you need l300 engine mounts for 4g63t dohc rwd, bt is that the rubber mounts that bolt onto crossmember or the mounts that bolt onto block to rubber mount, i have a sigma wit 4g32 if i only need l300 rubber mounts can i use old sigma mounts that bolt to block?

any ...

hay there just a quick question if you mount turbo in factory lowmounted position dose it have enough in engine bay to fit it like this???

just a few more picture of my finished water outlet housing and the start of my intake

http://i830.photobucket.com/albums/zz225/lilvr4/P1040941.jpg
http://i830.photobucket.com/albums/zz225/lilvr4/P1040940.jpg
http://i830.photobucket.com/albums/zz225/lilvr4/P1040939.jpg
http://i830 ...

would they flywheel off my 4g32 bolt up?

bellhouseing is not AWD its a RWD sigma

ohk i read that a FWDflywheel is what is needed as the ring gear lines up with starter motor, so what mitsi are FWD 7bolt?

Hi there , my mate is doin the same converion as me 4g63t dohc into a exlancer but he has a evo 4g63t with 7bolt he wont to know if there any flywheel that will match up to crank and line up with his starter motor on 5speed rwd gearbox? any help be great

run a ecu check mate , im guessing it your isc my 4g63t had same problem and crock isc or bad for ecu's

hi there im putting a 4g63t dohc egine into my sigma out of a vr4 galant im useing a 5speed sigma box with i beable to use vr4 flywheel and clutch or will i need sigma flywheel and clutch, if so will a 4speed flywheel and clutch work?

hay there i have a 1979 sigma im guna put sohc 4g63 turbo into
anything i need change like mounts ? and what about gearbox mines a cable clutch and 5speed with starion 4g63 is hydrolic

Hay there this is my 1978 sigma love it to bits
I planing to give it a planel and paint then drop a dohc 4g63t into it lower it more and get sum 17x7 17x8 advanti acutes


heres some picture of when i brought it off my grandma

http://i830.photobucket.com/albums/zz225/lilvr4/sigma3.jpg
http ...