Project Zero G Forums

I'm sending a LT1 Starion flywheel (CON2) to Bill and he is going to check it out.

I talked to Fidanza today and confirmed that they will make another run of the Starion LT1 flywheel if they can get 5-6 orders. This is basically a Starion flywheel drilled and cut to run the larger LT1 pressure plates which gives a lot more holding power.

I also have talked to a vendor that is ...

These are ready and Bill is just waiting for people to contact him and place orders. I have already done so and he said that the best way to contact him since he is sooo busy is to send him an email at japaneseauto1978@yahoo.com

Good shopping, David.

Let me know when/where to send the money also. I'm ready to go.

I'll take the transmission. I've got $600 right now and I have two customers that will be paying me sometime between tomorrow and Monday and then I will have the rest of the cash.

I can give you a $300 deposit now if you can wait until Monday for the rest.

David.

I totally understand the reason for wanting to have front exit and I want to do it on my build.

I just can't seem to wrap my mind around how the AE86 thermo housing works and how all the water hoses will need to be connected.

So assuming I want to actually have a heater and I want the front exit ...

I picked this bell housing up to match up to a 2.4L G4CS block but I just can't seem to find one anywhere near me. I was planning on putting it in my Starion (RWD) but it will bolt up to any FWD 4g63 or FWD 4g64 in a RWD configuration.

This is for an LT1 T56. Because I don't need it any more, this ...

Sounds good. I'm just trying to avoid one particular model number as it was weak in the syncros and was rated lower than the other years in HP/Torque capacity.

I'm still interested and trying to get the money together.

Can you tell me the exact model number that is stamped into it and how many miles it has?

I would get this and if I can find some way to swing it I will but I just kicked the wife out so I'm expecting to be short on funds now that I'm having to pay for everything myself.

If you really want to do it the right way then do what I'm going to do.

I'm going to be running of the hydro electric PS pumps from the new (2011+) v6 Jeeps to run not only my power steering but my brakes. I got the master cylinder from a Cobra Mustang that used Hydro Boost instead of a vacuum ...

Still in Austin but I have no idea how to ship an engine block!

Yes I still have it.

My condolences Bill.

Words just don't seem enough.

I was more thinking from the exhaust ports of the head. This would give the amount of overall room to fit the manifold and the turbo. I was previously thinking about going with a HX40 with a twin scroll turbine but I have since changed my mind an bought an HE351VE. It's even bigger but it will be an ...

The only difference is whether it is a 6-bolt or a 7-bolt which is determined by the number of bolts on the transmission side of the crank shaft. You can also tell by the oil pan right under the harmonic balancer on the crank shaft. If the pan has a dip in the pan under the balancer then it is a 7 ...

I looked into this a littl myself and it boiled down to this line that I read:
If I remember correctly 03-05 6 speed trannies on the 350z had a lot of issues with the syncros. Apparently issue was fixed in 2006... they run around $1200 used for 07-08

A lot of people in the forums talk about the ...

If you haven't already put the front end back together, I would really appreciate a lot of pictures showing how much room there is (or not) when you mount the exhaust manifold. With measurements between the frame of the car would be really appreciated.

I have checked every place I know of but all ...

I'm trying to find someone that has installed Bill Hinchers bell housing for the 93-97 LT1 T56 narrow block 4g63 in a Starion.

I want to know if the shifter gets moved forward or back from the stock position. How much and how far was the cylinder head from the firewall. Yes I realize that it ...

I'm trying to figure out how to mount a belt driven vacuum pump to a 1G motor but I don't have a full motor to look at right now.

I need pictures of a complete 1G motor with the power-steering, AC, and alternator with the belts still on with the motor on an engine stand.

Multiple angles would be ...

updated to sell...

check out the third line down from the pink line at the bottom of the engine list on this site at http://projectzerog.com/mitsubishi_engines.shtml

unless there is an error it is a G64B narrowblock in a 84-87 Galant

I'm not trying to argue...I'm just trying to confirm before I buy one.

In the FAQ on this site (and from Kane) it says that the G64B is a 2.4L WIDEBLOCK only! But in the list of Mitsubishi engines it has the G64B as both a wideblock and a NARROWBLOCK 6-bolt.

Can someone confirm (as in seen it, measured it) one way or the other?

Thankx, David.

I just got a good deal on a Bill Hincher T-56 narrow-block bell housing so now I need a narrow block 2.4 and not the wide-blocks that I have.

So I'm once again looking for a trade. If I find a narrow-block to purchase then I will sell these wide-blocks.

I really want to end up with a manual 6-speed transmission in my Starion. I currently have two 2.4 wideblock and I know I can get a narrowblock. I will also be running front exit water cooling and front mounted timing with NO CAS.

What are the options for a 6-speed transmission that will fit in the ...

Sorry, my mistake, I was thinking of the crank.

The 4g64 has longer 150mm rods to go with the larger 100mm stroke of the 4g64 crank.

I know the title is a litlle confusing. What I want is to get an idea of is how much traction the starquest has for straight line acceleration. So tell me what engine mods you have, what boost, what rpm, and speed you are going where the result is just spinning tires.

So for instance the stock ...

Sorry about this but I just got a message from Bill Hincher saying that he doesn't have any more of the T56 narrowblock bell housings. So until I can get some type of T56 bell housing I am going to have to hold off on changing what I have.

This actually explains something else that was mentioned on another forum.

It was mentioned that in drag racing it is preferable if the front tires are off the ground by a couple of inches so as to reduce the drag. It doesn't seem that there would be that much drag from those skinny front tires ...

So I've been told that when a Starquest starts getting a lot of power it will start having problems staying straight when accelerating even from 40mph.

Specifically, it was mentioned that in 2nd gear with an HX40 turbo that if you floor it then the car will get sideways.

I haven't had this problem ...

I'm looking for a mod for a T56 transmission that will detect what gear it is in?

Mainly I want to detect when it is in neutral for a remote start. So it needs to detect when it is in neutral rather than when it is NOT in neutral; that is it should assume it is not in neutral.

I don't have a 4g63 engine for a reference so I'm a little confused on the turbo oiling options/procedure when setting up a 4g64.

What I think a lot of people (especially myself) would like to see would be pics showing:
1. where the standard turbo oil port on a DOHC head is
2. how to block it off ...

I don't see how that monster would even fit behind the bumper much less the header panel or with the AC stuff. I live in Texas too and I'm not driving for 100+ days next summer in 100+ degree heat without AC.

Thankx but no thankx.

Does anyone have a starion with the front bumper off?

I'm trying to find the distance between the two frame rails where the stock intercooler sits so I can figure out what the maximum size of a new intercooler can be.

Thankx.

Where did you get that exhaust flange ?

I had found those articles previously but they all keep mentioning that the oil pan is curved and several other issues. The curved pan means that it would be technically a 2G but has 1G parts. But if you look at the 95 model as I mentioned above it says that it is compatible with a 91 which has a ...

I haven't verified this yet but this is what I have found and intend on trying.

* The 95 Hyundai Elantra/Sonata Oil Pump is compatible with the 1990 Mitsubishi Eclipse.
* The 95 Sonata used a crank mounted sensor.
* The 90 Eclipse is a 6-bolt
* So the 95 Sonata oil pump must be a 6-bolt with a ...

DJ, I can't seem to find any pics either. Your solution would work better than having to source specific parts.

Could you make up a bunch of extras or have Bill make them? There is a solution similar to yours but it runs ~$200 and I would rather support someone on here. I'm sure other people would ...

How much does it interfere? Do you have a pic?

IT is my business, if your willing to give me access DJ, I'll delete all the spam posts and add an image validation process to the posting routine that will stop future spaming.

Let me know if I can halp.

I have no problem with that but it will have to be paid in full first.

still up for sale

still up for sale

I'll reply via PM.

Check out the item at the bottom of this page. It is a 1 1/4" Hose to 1 1/4" Hose with Closeable 1 1/4" bypass port custom thermo valve like what Bill mentions.

http://www.ipsco.org/Custom%20Services/ ... custom.htm

Check out the item at the bottom of this page. It is a 1 1/4" Hose to 1 1/4" Hose with Closeable 1 1/4" bypass port custom thermo valve like what Bill mentions.

http://www.ipsco.org/Custom%20Services/ ... custom.htm

I would be willing to do $1100 shipped if you bought both.

Project Zero G Forums

Search found 108 matches

Fidanza LT1 flywheel for Bills T56 bellhousing

FS: T-56 4g63 bell housing for FWD narrow-block motor

Has anyone installed Bills T56 bell housing in a Starion?

I need pics of a 1g motor with all belts on an engine stand

Is the G64B available as wideblock and narrowblock ?

What are the manual 6-speed transmission options?

At what point does a StarQuest loose acceleration traction?

What would cause a Starquest to get sideways when accelerati

Is there a mod for a T56 to detect what gear your in?

Can someone post a write up on 4g64 tubo oiling options?

Distance between frame rails on a Starion?